Leaf Filter & Gutter Guard Installation in Langley, Surrey & the Lower Mainland
Typical home$20/ftbefore GST
Leaf filter installation costs $20 per foot of gutter, installed, before GST. We measure your gutter runs for free and give you the total before any work starts.
Every install starts with a full gutter clean and downspout flush, so the system starts clear. Then stainless micro-mesh guards are fitted to your existing gutters. Rain goes through; leaves, cedar needles and roof grit stay on top, dry out and blow off.
- Licensed & Insured
- 100% Satisfaction Guarantee
- Free Quotes, No Obligation
- 24-Hour Quote Response
Micro-mesh vs foam vs surface-tension gutter guards
Foam inserts sit inside the gutter. Fine debris settles into the foam, and in our wet climate it can end up growing moss, so the insert has to come out and be cleaned or replaced. Surface-tension guards (the curved-lip type) count on water following the curve into the gutter. In a heavy downpour some of it overshoots. Perforated covers let cedar and fir needles fall straight through the holes.
Micro-mesh has openings smaller than a needle is wide, so needles stay on the surface. That is why we install it here, where cedar, fir and hemlock needles are the main thing clogging gutters.
Why book leaf filter installation with us
End routine cleanings
Micro-mesh keeps out leaves, cedar needles and moss debris, the three main gutter cloggers in our region.
Handles BC rain
Fine mesh lets heavy rain through while the debris stays on top.
Fits existing gutters
Installed on your current gutters. No gutter replacement needed.
Cleaned before install
Every installation includes a full gutter clean and downspout flush first.
Our process
- 1
Measure & assess
We measure the gutter runs and check pitch, fastening and the roof edge. At $20 per foot, you get the total up front.
- 2
Full gutter clean
Gutters and downspouts are cleaned and flushed so the system starts clear.
- 3
Precision installation
Guards are cut and fastened to your gutter profile for a secure, low-profile fit.
- 4
Water test
We test the flow across the system and walk you through the finished work.
How a micro-mesh gutter guard works
Once it is fitted you will never see the part that does the work. So here it is in section: where the mesh sits, what happens to the rain, and what happens to everything else.
Why mesh, and not a perforated cover
The cheap covers sold at hardware stores are punched sheet with holes big enough to see through. That is fine under a maple and useless under a cedar. Needles drop straight through the holes and pack the trough solid, except now there is a lid screwed over the top of the mess.
Fine stainless mesh is chosen for the Lower Mainland specifically because cedar, fir and hemlock needles are the local problem. The apertures are smaller than a needle is wide, so the needles stay on the surface, dry out, and blow off.
What installation day looks like
Most installs are a single visit. Here is the whole sequence, including the two steps people are usually surprised we do at all.
- 1
Measure and assess
Before install dayWe measure every gutter run, check the pitch and the fascia fixings, and look at what drops on the roof: maple, cedar, fir or all three. If a section of gutter is sagging, split or pulling away, we tell you before it gets covered.
- 2
Full clean and downspout flush
Install day, firstEvery run is hand-cleared and every downspout flushed until it runs free. This is not an upsell, it is the reason the system works: mesh fitted over a gutter that is already half full traps that debris underneath, where nobody can reach it.
- 3
Mesh cut and fastened to the gutter
The install itselfPanels are cut to your gutter's profile and fastened along both edges: the inner lip and the outer lip. Nothing is slipped under your shingles and nothing is nailed through the roof deck, so your roofing warranty is untouched. Corners, miters and end caps are cut and fitted one by one.
- 4
Water test the whole system
Before we pack upWe run water across the roof at volume and watch every run, every join and every downspout. A guard that handles drizzle but sheets water over the front edge in a real downpour has failed, and the only way to know is to make it rain.
- 5
Walkthrough and handover
FinishWe walk you round the finished work, show you what the mesh looks like from the ground, and tell you what maintenance is left: an occasional brush-off of the guard surface, not a twice-yearly clean-out.
The product, in plain terms
No lifetime-miracle claims. This is what the system is and what it does.
- Filter medium
- Stainless steel micro-mesh, fine enough to stop cedar and fir needles as well as leaf litter
- Fixing method
- Fastened to the gutter's inner and outer lip, never under the shingles, never through the roof deck
- Fits
- Your existing gutters, in place. No gutter replacement, and no change to your downspouts
- Rain handling
- Fine mesh lets rain straight through. Every install is water tested before we leave
- Included
- Full gutter clean and downspout flush before fitting, plus a water test afterwards
- Ongoing care
- Debris dries on the surface and blows off. Expect an occasional brush-down, not a clean-out
We install generic stainless micro-mesh gutter guards, fitted to your existing gutters. We are happy to show you the exact product on site and talk through why it suits your roof, your tree cover and your budget before you commit to anything.
Real results, every visit
We photograph before and after on every job so you can see exactly what you paid for. Browse the gallery for more leaf filter installation transformations.
View Before & After GalleryLeaf Filter Installation across the Lower Mainland
We bring leaf filter installation to homes in every corner of the Lower Mainland. Find your city:
Leaf Filter Installation FAQs
How much does leaf filter installation cost?
$20 per foot of gutter, installed, before GST. We measure your gutter runs for free, so you know the total before we start. Every install begins with a full gutter clean and downspout flush.
Which gutter guard is best: micro-mesh, foam or surface-tension?
For Lower Mainland homes under cedars and firs, micro-mesh. Needles fall through perforated covers, foam inserts trap fine debris and can grow moss, and surface-tension guards can let heavy rain overshoot. Micro-mesh openings are smaller than a needle is wide.
How do you clean gutters that have guards on them?
Usually you only brush the top of the mesh every 1 to 2 years, because debris dries and blows off. If an older guard has let debris in underneath, it has to come off so the gutter can be cleaned, then go back on.
Do leaf filters really work with cedar needles?
Fine micro-mesh does. Needle-shedding cedars and firs are exactly why we install fine mesh rather than cheap perforated covers.
Can filters be installed on old gutters?
Usually yes, if the gutters are sound. We check first and tell you if a section needs repair before it is worth covering.
Do gutter guards affect my roof warranty?
No. Our guards fasten to the gutter, not under your shingles, so roofing warranties are not affected.
Our 100% satisfaction guarantee
If you're not completely happy with your leaf filter installation, we'll come back and make it right at no extra cost.
Get a free leaf filter installation quote
Takes 60 seconds. We'll reply within 24 hours with a no-obligation quote for your home.
- Licensed & Insured
- 100% Satisfaction Guarantee
- Free Quotes, No Obligation
- 24-Hour Quote Response
Ready to restore your home's exterior?
Free quotes within 24 hours. Fully insured, eco-friendly, and backed by our 100% satisfaction guarantee across the Lower Mainland.